One Control Tuner with BJF buffer

The signal travels a long journey until the signal output from the guitar enters the pedal board and is transmitted to the amplifier via the effector and switcher.
Patch cables, plugs and jacks ... Effects of each are small, but the sound may change greatly due to overlapping.
The signal continues to decay while passing through the shielded cable. The longer the cable, the greater the effect.

To prevent the signal from weakening due to these factors, the signal is routed through a buffer.

In the past, many pedal tuners had built-in buffers. Usually, a buffer is built into the pedal tuner installed at the top of the board to mitigate subsequent signal decay.
However, the buffer changed the sound. It is undesirable for a tuner to simply measure the signal to change the sound. In response to this, True Bypass pedal tuners have become commonplace.

The tuner should not change the sound significantly. However, the benefits of having a buffer built into the tuner are significant.
If you can do both at the same time, you won't have to stick to true bypass. In other words, you just need a buffer that doesn't change the sound a lot.

● BJF BUFFER
The BJF BUFFER installed in many switchers of One Control is this overwhelmingly natural buffer that overturns the image held in many “buffers”.

・ Set the gain to exactly 1.
・ Do not change the sound with the input impedance.
・ Do not make output too strong.
・ Minimize noise to the limit.
・ Make sure the sound doesn't get worse when overloaded.

Completed to meet the requirements of BJF's particular buffer, BJF Buffer helps guitar signals at the feet of many professionals around the world.

Even when bypassed, the natural tone is not destroyed, and at the same time the signal itself is strengthened to prevent attenuation due to the effects of cables and terminals. When the tuner is on, the output can be muted to tune comfortably.
In addition, a small housing that does not take up extra space on the pedal board allows you to maximize the pedal board area.

One Control Minimal Series Tuner with BJF BUFFER -TUNE POWERED BY KORG- is the form of tuner that all guitarists / bassists have sought.

● Powerful tuner
Minimal Series Tuner uses KORG PitchBlack Mini in the tuner section.
Equipped with a large display with good visibility even in a small housing, achieving high responsiveness and accuracy.

● 3 display modes
The Minimal Series Tuner can be tuned in three display modes.
“Regular” mode with the most standard display suitable for stage tuning, “Strobe mode” that can drive tuning with ultra-high accuracy of ± 0.1 cents, and optimal for guitar intonation adjustment, and two displays You can select the “half strobe mode” that combines the modes.

● Calibration settings for a wide range of concert pitches
The Minimal Series Tuner can set the reference pitch at A4 = 436 to 445Hz (1Hz step). Just changing the reference pitch by 1Hz may make the music image completely different. By adapting to various concert pitches, you can tune with confidence regardless of your play style.

● Supports battery operation
Minimal Series Tuner can be driven by two CR1632 button batteries in addition to the standard center minus DC9V adapter.
It can be used as an auxiliary power source in case of trouble, or in many situations such as tuning in places where power cannot be removed.

● Convenience of pedal tuners In recent years, clip tuners with built-in clip-type microphones that pick up vibrations from the head and body are also increasing.
A convenient and convenient clip tuner can inevitably pick up the vibration and pitch of other instruments when tuning on a live stage where loud sounds are produced.
The pedal tuner directly detects the signal from the guitar / bass, so you can tune reliably and quickly on stage.

● Specifications ・ BJF BUFFER (when tuner bypass)
Input impedance: 500KΩ
Output impedance: 60Ω or less

・ Tuner (KORG PitchBlack Mini)
Temperament: 12 Average temperament Measurement range: E0 (20.60Hz) to C8 (4186Hz)
Reference pitch range: A4 = 436 to 445Hz (1Hz step)
Input impedance: 1MΩ (when tuner is ON)

・ Power adapter: DC9V adapter, center minus, inner diameter 2.1mm (One Control EPA-2000 recommended)
Battery: CR1632 lithium battery x 2
Battery life: When the tuner is on, continuous approximately 2 hours (when continuous input, display mode: regular)
Current consumption: Up to 40mA

・ Size: 94D × 44W × 47H mm (including protrusions)
・ Weight: 134g

* Battery is not included.