• +358406810910
  • Express shipping available
  • Returns within 14 days
  • nordsoundfi@gmail.com
  • Stock items
  • +358406810910
  • Express shipping available
  • Returns within 14 days
  • nordsoundfi@gmail.com
  • Stock items

Taurus Stomp-Head 7.Apogee - RED (Käytetty)

Tuotenumero: TS-SH7

OVH860,00 €
−23 %
665,00 €
Varastossa meillä
Toimitusaika: 1-3 päivä(ä)

Kuvaus

Taurus Stomp-Head 7.Apogee - Used, but in perfect condition!


A real analog amplifier gives more satisfaction than a whole lot of digital simulations based on iconic amps. The SH7 Apogee, designed with its own character and powerful sound
is a modern, practical tool for guitarists who prefer a traditional analog tube sound.

The Taurus Stomp-Head 7 is a fully analog design based on our own Master Tube Design technology, without any digital simulations. Extremely light and compact but still very powerful and versatile.
If extensive sound creation capabilities is preferred, the SH-7.CE will be the right choice for you.

The Taurus SH-7 can be used in various configurations:

  • as a classic amplifier with a speaker cabinet.
    There are 4 power levels to choose from: 90W, 40W, 20W and 12W.
  • as a preamp connected directly to the mixer or sound system using output with built-in loudspeaker simulation.

Stomp-Head 7 as a pre-amp.
If you want to record your guitar or use the amplifier as a pre-amp without a cabinet then you have a special tool on board - an advanced loudspeaker simulator (IR-Cab simulation). You can choose accurate simulations of two types of speakers: Celestion Vintage-30 and Celestion Creamback. Also two types of cabinets with different dimensions - small and large can be chosen.
A simulation of the microphone position is also available and provides additional possibilities of equalizing the colour of your sound at the line output. Thanks to this solution you can get closer to the sound conditions of a classic set of speakers with a microphone setup. You get the right placement and sound of the instrument in the band's mix by transmitting the signal from the line output without using the speaker. All this is done in an analog way, very simple and intuitive, without the use other additional processors. The line output has two signals paths, with or without simulation. This feature also allows you to connect an external loudspeaker simulator. So you can use the built-in simulation, external simulation or both of them at once.

Specification:

  • Power stage efficiency: 200Watt
  • Power output selector: 90W, 40W, 20W, 12W
  • Speakers impedance auto detection: 4, 8 and 16ohm
  • Tubes: 12AX7
  • 2 channels: CLEAN+CRUNCH and LEAD
  • 5 footswitches: CLEAN, CRUNCH, DRIVE, REVERB, BOOST

    CHANNEL controls (CLEAN & LEAD):
  • GAIN, BASS, MIDDLE, MID-RANGE switch, TREBLE, PRESENCE, VOLUME

    MASTER controls:
  • SERVO – analog enhancer level with SERVO GAIN switch
  • BOOST - access to set two different volume levels
  • REVERB
  • NOISE GATE
  • MUTE
  • input GAIN boost (switch +6dB)
  • RESONANCE – switch increasing the sound in the resonance range of the loudspeaker
  • Serial EFFECT LOOP
  • LINE OUTPUT with Speaker Simulation. Allows send linear signal with simulation (PIN) or without simulation (RING) or both simultaneously
  • EXTERNAL CONTROLLER INPUT for channel selector and BOOST
  • Voltage selector 230V/50Hz or 115V/60Hz
  • Dimensions: (H x W x D) 90 x 330 x 205 mm
  • Weight: 2,65kg